View AP716510_4960889.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

AP7165
600mA LOW DROPOUT REGULATOR WITH POK
Description
The AP7165 is a 600mA, adjustable output voltage, ultra-low dropout linear regulator. The device includes pass element, error amplifier, band-gap reference, current limit and thermal shutdown circuitry. The device is turned on when EN pin is set to logic high level. A Power-OK (POK) output is available for power sequence control. The characteristics of the low dropout voltage and low quiescent current make it suitable for low to medium power applications, for example, laptop computers, audio and video applications, and battery powered devices. The typical quiescent current is approximately 125A. Built-in current-limit and thermal-shutdown functions prevent IC from damage in fault conditions. The AP7165 are available in DFN3030-10 and SOP-8L-EP packages.
Pin Assignments
( Top View )
IN IN POK NC EN
1 2 3 4 5 10 9 8 7 6
OUT OUT FB NC GND
DFN3030-10
( Top View )
IN 1 2 3 4 8 7 6 5 OUT OUT FB GND
Features
IN
* * * * * * * * * * * * *
Wide input voltage range: 2.2V - 5.5V 300mV very low dropout at 500mA load Very low quiescent current (IQ): 125A typical Adjustable output voltage range: 0.8V to 5.0V Very fast transient response High PSRR Accurate voltage regulation Current limiting and short circuit protection Thermal shutdown protection Stable with any type output capacitor 4.7F Ambient temperature range -40C to 85C DFN3030-10 and SOP-8L-EP: Available in "Green" Molding Compound (No Br, Sb) Lead Free Finish/RoHS Compliant (Note 1)
POK EN
SOP-8L-EP
Applications
* * * * * *
Servers and laptops Smart phone and PDA MP3/MP4 Bluetooth headset Low and medium power applications FPGA and DSP core or I/O power
Notes:
1. EU Directive 2002/95/EC (RoHS). All applicable RoHS exemptions applied. Please visit our website at http://www.diodes.com/products/lead_free.html.
AP7165
Document number: DS31270 Rev. 6 - 2
1 of 14 www.diodes.com
September 2010
(c) Diodes Incorporated
AP7165
600mA LOW DROPOUT REGULATOR WITH POK Typical Application Circuit
VIN
IN 100kOhm 1F POK AP7165 FB R2 Enable EN GND OUT R1
VOUT
10F
R VOUT = VREF 1 + 1 R2
Pin Descriptions
Name Pin # DFN3030-10 SOP-8L-EP Description
IN POK EN GND FB OUT NC
1, 2 3 5 6 8 9, 10 4, 7
1, 2 3 4 5 6 7, 8 NA
Voltage input pins, to be tied together externally. Bypass to ground through at least 1F capacitor. Power-OK output, active-high open-drain. Enable input, active high. Ground. Output feedback. Voltage output pins, to be tied together externally. Bypass to ground through at least 4.7F ceramic capacitor. No connection.
AP7165
Document number: DS31270 Rev. 6 - 2
2 of 14 www.diodes.com
September 2010
(c) Diodes Incorporated
AP7165
600mA LOW DROPOUT REGULATOR WITH POK Functional Block Diagram
IN
Current Limit and Thermal Shutdown
OUT
EN
Gate Driver
FB POK
0.8V
0.744V
GND
Absolute Maximum Ratings
Symbol Parameter Ratings Unit
ESD HBM ESD MM VIN
Human Body Model ESD Protection Machine Model ESD Protection Input Voltage OUT, FB, POK, EN Voltage Continuous Load Current
4 300 7 VIN + 0.3 Internal Limited 150 -65 ~150
KV V V V
TJmax TST PD
Notes:
Maximum Junction Temperature Storage Temperature Range Power Dissipation DFN3030-10 (Note 2, 4) SOP-8L-EP (Note 2, 5)
C C W W
3.1 4.0
2. Ratings apply to ambient temperature at 25C
Recommended Operating Conditions
Symbol VIN IOUT TA Parameter Input voltage Output Current Operating Ambient Temperature Min 2.2 0 -40 Max 5.5 600 85 Unit V mA C
AP7165
Document number: DS31270 Rev. 6 - 2
3 of 14 www.diodes.com
September 2010
(c) Diodes Incorporated
AP7165
600mA LOW DROPOUT REGULATOR WITH POK Electrical Characteristics
(TA = 25oC, VIN = VOUT +1V, CIN = 1F, COUT = 10F, VEN = VIN, unless otherwise stated)
Symbol Parameter Test Conditions Min -1 Typ. Max Unit
IQ ISHDN VROPOUT VREF IFB VOUT
Input Quiescent Current Input Shutdown Current Dropout Voltage FB reference voltage FB leakage Output Voltage Total Accuracy Line Regulation Load Regulation Start-up Time, from EN high to POK high Power Supply Rejection Ratio Current limit Short-circuit Current EN Input Logic Low Voltage EN Input Logic High Voltage EN Input leakage POK output low voltage
IOUT = 0 VEN = 0V, IOUT = 0 (Note 3) VOUT 1.5V, IOU T = 500mA
-2.5
125 0.01 300 0.8 0.01
170 1 400 1 2.5
A A mV V A % %/V
VOUT / VOUT VIN
VOUT / VOUT
VIN = VOUT +1V to 5.5V, IOUT = 1mA IOUT from 1mA to 500mA VEN = 0V to 2.0V, IOUT = 100mA, VIN = 3.3V 1kHz, VIN = 3.3V, VOUT = 1.2V, IOUT = 0mA VOUT = 1.8V, ROUT = 0.5 VIN = 3.3V, VOUT < 0.2V -1.0
0.015 1.0 170 60 600 950 380 0.4 1.4 87% 0.01 100 92% 4% 150 0.01 150 25 40 27 9 4 1 200 97%
% s dB mA mA V V A mV Vref Vref s A C C
o o o o
tST PSRR ILIMIT ISHORT VIL VIH IEN VOL VPOK_TH_UP VPOK Hys POK deglitch IPOK LK TSHDN THYS
JA
VEN = 0V or 5.5V Force 2mA FB (or OUT for fixed version) Output voltage (rising) POK threshold rising Output voltage POK hysteresis VIN = 3.3V, VOUT = 1.2V POK leakage current VPOK = 5.5V Thermal shutdown threshold Thermal shutdown hysteresis Thermal Resistance Junction-toAmbient Thermal Resistance Junction-to- Case DFN3030-10 (Note 4) SOP-8L-EP (Note 5) DFN3030-10 (Note 4) SOP-8L-EP (Note 5)
1
C/W C/W C/W C/W
JC
Notes:
3. POK pin must be disconnected from IN pin. 4. Test condition for DFN3030-10: Device mounted on FR-4 2-layer board, 2oz copper, with minimum recommended pad on top layer and 6 vias to bottom layer 1.0"x1.5" ground plane. 5. Test condition for SOP-8L-EP: Device mounted on 2" x 2" FR-4 substrate PCB, 2oz copper, with minimum recommended pad on top layer and thermal vias to bottom layer ground plane.
AP7165
Document number: DS31270 Rev. 6 - 2
4 of 14 www.diodes.com
September 2010
(c) Diodes Incorporated
AP7165
600mA LOW DROPOUT REGULATOR WITH POK Typical Performance Characteristics
Output Voltage vs. Temperature
3.40 Vout=3.3V 1.90
Output Voltage vs. Temperature
Vout=1.8V
Output Voltage (V)
Output Voltage (V)
-50 -25 0 25 50 75 100 125
3.35
1.85
3.30
1.80
3.25
1.75
3.20
1.70 -50 -25 0 25 50 75 100 125
Temperature ( C)
o
Temperature ( C)
o
Quiescent Current vs. Input Voltage
170
Quiescent Current vs. Input Voltage
170 160 150 140 130 120 110 100 90 Iout=0mA Iout=300mA Iout=600mA 2.5 3.0 3.5 4.0 4.5 5.0 5.5
VOUT=1.2V
VOUT=1.8V
160 150 140 130 120 110
Iout=0mA
100 90 2.5 3.0 3.5 4.0 4.5 5.0 5.5
Iout=300mA
Quiescent Current ( uA)
Quiescent Current (uA)
Input Voltage (V)
Input Voltage (V)
Quiescent Current vs. Temperature
150 150
Quiescent Current vs. IOUT
VOUT=1.8V
Quiescent Current (uA)
140 130 120 110 100 VIN=2.2V, Vout=1.0V 90 80 70 -50 -25 0 25 50 75 100 125 VIN=3.3V, Vout=1.2V VIN=3.3V, Vout=1.8V VIN=5.0V, Vout=3.3V
Quiescent Current (uA)
140
130
120
110
VIN=2.5V VIN=3.3V
100 0.0 0.1 0.2 0.3 0.4 0.5 0.6
Temperature ( C)
o
IOUT (A)
AP7165
Document number: DS31270 Rev. 6 - 2
5 of 14 www.diodes.com
September 2010
(c) Diodes Incorporated
AP7165
600mA LOW DROPOUT REGULATOR WITH POK Typical Performance Characteristics (Continued)
Reference Voltage vs. Temperature
0.810
Dropout Voltage vs. I OU T
VOUT=3.3V
400
Reference Voltage (V)
Dropout Voltage (mV )
25C 350 300 250 200 150 100 50 0 90C -45C
0.805
0.800
0.795
0.790
Vin=2.2V
0.785
Vin=3.3V Vin=5.5V
0.780 -50 -25 0 25 50 75 100 125
0
100
200
300
400
500
600
Temperature ( C)
o
I OU T (mA)
Line Regulation
VOUT=1.2V, IOUT=1mA
0.10
Load Regulation
VIN=2.5V, VOUT=1.2V
0.6
Change in VOUT (%/V)
Change in V OUT (%)
25C 0.5 0.4 0.3 0.2 0.1 0.0 0.0 0.1 0.2 0.3 0.4 0.5 0.6 85C -40C
0.05
0.00
-0.05
25C 85C -40C
-0.10 2.5 3.0 3.5 4.0 4.5 5.0 5.5
VIN (V)
IOUT (A)
Current Limit vs. Temperature
1.08 1.06
PSRR (VOUT=1.2V) -40 -50 PSRR (dB) -60 -70 -80
Current Limit (A)
1.04 1.02 1.00 0.98 0.96 0.94
Vin=2.8V, Vout=1.8V
0.92 0.90 -50 -25 0 25 50 75 100
Vin=3.3V, Vout=1.8V
-90 100
1000
10000
100000
Temperature ( C)
o
Frequency (Hz)
AP7165
Document number: DS31270 Rev. 6 - 2
6 of 14 www.diodes.com
September 2010
(c) Diodes Incorporated
AP7165
600mA LOW DROPOUT REGULATOR WITH POK
Typical Performance Characteristics (Continued) Line Transient Response
VIN =3.3V to 4.4V COUT =10uF
Line Transient Response
VIN =4.4V to 3.3V COUT =10uF
VIN 1V/div
VIN 1V/div
VOUT 50mV/div
VOUT 50mV/div
Time (50us/div)
Time (50us/div)
Output Load Transient Response (VOUT=1.2V) COUT=470uF (electrolytic)
VOUT 50mV/div COUT=1uF (Ceramic) COUT=10uF (Ceramic) VOUT 50mV/div
Output Load Transient Response (VOUT=1.8V) COUT=470uF (electrolytic)
COUT=10uF (Ceramic)
COUT=1uF (Ceramic)
600mA
600mA
IOU 200mA/div 50mA
1A/us
IOU 200mA/div 50mA
1A/us
Time (100us/div)
Start-up Time (VOUT=1.2V, IOUT=0.1A)
VEN 2V/div
Time (100us/div) Start-up Time (VOUT=1.2V, IOUT=600mA)
VEN 2V/div
COUT=10uF VOUT 1V/div VOUT 1V/div
COUT=10uF
VPOK 2V/div
VPOK 2V/div
Time (50us/div)
AP7165
Document number: DS31270 Rev. 6 - 2
Time (50us/div)
7 of 14 www.diodes.com September 2010
(c) Diodes Incorporated
AP7165
600mA LOW DROPOUT REGULATOR WITH POK
Typical Performance Characteristics (Continued)
Short Circuit Current vs. Input Voltage Short Circuit Current (mA)
420 410 400 390 380 370 360 350 2.0 2.5 3.0 3.5 4.0 4.5 5.0
Short Circuit Current vs. Tem perature
500
VOUT=1.2V
VOUT=1.2V
Short Circuit Current (mA)
450
400
350
300 -50 -25 0 25 50 75
Input Voltage (V)
Tem perature ( C)
o
Current Limit Protection (VOUT=1.8V)
VOUT 500mV/div
Current Limit & Short Circuit Protection (VOUT=0.8V)
VOUT 500mV/div
IOUT 500mA/div
Current Limit Protection
IOUT 1A/div
Short Circuit Protection
Time (50us/div)
Time (500us/div)
Short Circuit Protection (VOUT=1.8V)
Short Circuit Recovery (VOUT=1.8V)
VOUT 500mV/div
VOUT 500mV/div
Current Limit Protection
IOUT 500mA/div
Short Circuit Protection
IOUT 500mA/div
Time (2ms/div)
AP7165
Document number: DS31270 Rev. 6 - 2
Time (50us/div)
8 of 14 www.diodes.com September 2010
(c) Diodes Incorporated
AP7165
600mA LOW DROPOUT REGULATOR WITH POK Application Notes
Input Capacitor
A 1F ceramic capacitor is recommended to connect between IN and GND pins to decouple input power supply glitch and noise. The amount of the capacitance may be increased without limit. A lower ESR (Equivalent Series Resistance) capacitor allows the use of less capacitance, while higher ESR type requires more capacitance. This input capacitor should be located as close as possible to the device to assure input stability and less noise. For PCB layout, a wide copper trace is required for both IN and GND. Rearranging the equation will give the following equation to find the approximate resistor divider values:
V R 1 = R 2 OUT - 1 V REF
To maintain the stability of the internal reference voltage, R2 needs to be kept smaller than 250k.
No Load Stability Output Capacitor
The output capacitor is required to stabilize and help the transient response of the LDO. The AP7165 is designed to have excellent transient response for most applications with a small amount of output capacitance. The AP7165 is stable for all available types and values of output capacitors 4.7F. The device is also stable with multiple capacitors in parallel, which can be of any type of value. Additional capacitance helps to reduce undershoot and overshoot during transient. This capacitor should be placed as close as possible to OUT and GND pins for optimum performance. Other than external resistor divider, no minimum load is required to keep the device stable. The device will remain stable and regulated in no load condition.
ENABLE/SHUTDOWN Operation
The AP7165 is turned on by setting the EN pin high, and is turned off by pulling it low. If this feature is not used, the EN pin should be tied to IN pin to keep the regulator output on at all time. To ensure proper operation, the signal source used to drive the EN pin must be able to swing above and below the specified turn-on/off voltage thresholds listed in the Electrical Characteristics section under VIL and VIH.
Adjustable Operation
The AP7165 provides output voltage from 0.8V to 5.0V through external resistor divider as shown below.
POWER-OK
The Power-Ok (POK) pin is an active high open-drain output. It can be connected to any 5.5V or lower rail through an external pull-up resistor. The recommended sink current of POK pin is up to 4mA, so the pull-up resistor for POK should be in the range of 10k to 1M. If output voltage monitoring is not needed, the POK pin can be left floating.
VIN
IN OUT R1 FB R2 Enable EN GND
VOUT
CIN
100kOhm
AP7165 POK
COUT
Current Limit Protection
When output current at OUT pin is higher than current limit threshold, the current limit protection will be triggered and clamp the output current to approximately 950mA (600A min) to prevent over-current and to protect the regulator from damage due to overheating.
The output voltage is calculated by:
Short Circuit Protection
When OUT pin is short-circuited to GND or OUT pin voltage is less than 200mV, short circuit protection will be triggered and clamp the output current to approximately 380mA. This feature protects the regulator from overcurrent and damage due to overheating.
R VOUT = VREF 1 + 1 R 2
Where VREF=0.8V (the internal reference voltage).
AP7165
Document number: DS31270 Rev. 6 - 2
9 of 14 www.diodes.com
September 2010
(c) Diodes Incorporated
AP7165
600mA LOW DROPOUT REGULATOR WITH POK
Application Notes (Continued)
Low Quiescent Current
The AP7165, consuming only around 125A for all input range and output loading, provides great power saving in portable and low power applications. thermal plane that is connected to the thermal pad is critical to avoid thermal shutdown and ensuring reliable operation. Power dissipation of the device depends on input voltage and load conditions and can be calculated by:
Wide Output Range
The AP7165, with a wide output range of 0.8V to 5.0V, provides a versatile solution for many portable and low power applications.
PD = ( VIN - VOUT )xIOUT
The AP7165 is available in the DFN3030-10 and SOP-8LEP packages, both with exposed pad, which is the primary conduction path for heat to the printed circuit board (PCB). The pad can be connected to ground or be left floating; however, to ensure the device will not overheat, it should be attached to an appropriate amount of copper PCB area. However, the maximum power dissipation that can be handled by the device depends on the maximum junction to ambient thermal resistance, maximum ambient temperature, and maximum device junction temperature, which can be approximated by the equation below:
Thermal Shutdown Protection
Thermal protection disables the output when the junction temperature rises to approximately +150C, allowing the device to cool down. When the junction temperature reduces to approximately +125C the output circuitry is enabled again. Depending on power dissipation, thermal resistance, and ambient temperature, the thermal protection circuit may cycle on and off. This cycling limits the heat dissipation of the regulator, protecting it from damage due to overheating.
Power Dissipation
The device power dissipation and proper sizing of the
PD (max@ TA ) =
( +145C - TA ) R JA
AP7165
Document number: DS31252 Rev. 6 - 2
10 of 14 www.diodes.com
September 2010
(c) Diodes Incorporated
AP7165
600mA LOW DROPOUT REGULATOR WITH POK Ordering Information
AP7165 - XX G - X
Package FN : DFN3030-10 SP : SOP-8L-EP
Device Package Code Packaging (Note 2)
Green G : Green
Packing 7/13 : Tape & Reel
AP7165-FNG-7 AP7165-SPG-13
Notes:
FN SP
DFN3030-10 SOP-8L-EP
Tube Part Number Quantity Suffix NA NA NA NA
7"/13" Tape and Reel Quantity Part Number Suffix
3000/Tape & Reel 2500/Tape & Reel
-7 -13
6. Pad layout as shown on Diodes Inc. suggested pad layout document AP02001, which can be found on our website at http://www.diodes.com/datasheets/ap02001.pdf.
Marking Information
(1) DFN3030-10
( Top View ) XX YWX
XX : Identification Code Y : Year : 0~9 W : Week : A~Z : 1~26 week; a~z : 27~52 week; z represents 52 and 53 week X : A~Z : Green
Package DFN3030-10 Identification Code B2
Part Number AP7165
(2) SOP-8L-EP
( Top View )
8 5
Logo Part No. AP7165 YY WW X X E
1 4
G : Green YY : Year : 08, 09,10~ WW : Week : 01~52; 52 represents 52 and 53 week X : Internal Code SOP-8L-EP
AP7165
Document number: DS31252 Rev. 6 - 2
11 of 14 www.diodes.com
September 2010
(c) Diodes Incorporated
AP7165
600mA LOW DROPOUT REGULATOR WITH POK Package Outline Dimensions (Continued)
(1) Package Type: DFN3030-10
TOP MARK
0.10 C 0.08 C 0.57/0.63 0/0.02
0.15
Seating Plane
Top View
10x-0.30 0.50Typ. 0.60
0.25 A
Side View
2.9/3.1 2.3/2.5
C
2X-
(Pin #1 ID)
1.80
2.9/3.1
1.5/1.7
R0 .30
0.25/0.55
2.60 Land Pattern Recommendation (Unit:mm)
2X-
0.25 B 0.375Typ.
0.50Typ.
0.20/0.30
0.10
CAB
Bottom View
(2) Package Type: SOP-8L-EP
Detail "A" Exposed pad
7~9
3.85/3.95
5.90/6.10
3.70/4.10
45 0.35max.
7~9 1 1.30/1.50 1.75max.
0.15/0.25 3.3Ref.
1
Bottom View
0/0.13
0.254
1.27typ 4.85/4.95 1
0.3/0.5
Gauge Plane Seating Plane
0.62/0.82
Detail "A"
8x-0.60
Exposed pad
6x-1.27 8x-1.55
Land Pattem Recommendation (Unit:mm)
Notes:
7. All dimensions are in millimeters. Angles are in degrees. 8. Coplanarity applies to the exposed heat sink slug as well as the terminals.
5.4
AP7165
Document number: DS31252 Rev. 6 - 2
12 of 14 www.diodes.com
2.4Ref.
0.15
0.15
B
A
September 2010
(c) Diodes Incorporated
AP7165
600mA LOW DROPOUT REGULATOR WITH POK Taping Orientation (Note 9)
For DFN3030-10
Notes:
9.The taping orientation of the other package type can be found on our website at http://www.diodes.com/datasheets/ap02007.pdf.
AP7165
Document number: DS31252 Rev. 6 - 2
13 of 14 www.diodes.com
September 2010
(c) Diodes Incorporated
AP7165
600mA LOW DROPOUT REGULATOR WITH POK
IMPORTANT NOTICE DIODES INCORPORATED MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARDS TO THIS DOCUMENT, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION). Diodes Incorporated and its subsidiaries reserve the right to make modifications, enhancements, improvements, corrections or other changes without further notice to this document and any product described herein. Diodes Incorporated does not assume any liability arising out of the application or use of this document or any product described herein; neither does Diodes Incorporated convey any license under its patent or trademark rights, nor the rights of others. Any Customer or user of this document or products described herein in such applications shall assume all risks of such use and will agree to hold Diodes Incorporated and all the companies whose products are represented on Diodes Incorporated website, harmless against all damages. Diodes Incorporated does not warrant or accept any liability whatsoever in respect of any products purchased through unauthorized sales channel. Should Customers purchase or use Diodes Incorporated products for any unintended or unauthorized application, Customers shall indemnify and hold Diodes Incorporated and its representatives harmless against all claims, damages, expenses, and attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized application. Products described herein may be covered by one or more United States, international or foreign patents pending. Product names and markings noted herein may also be covered by one or more United States, international or foreign trademarks. LIFE SUPPORT Diodes Incorporated products are specifically not authorized for use as critical components in life support devices or systems without the express written approval of the Chief Executive Officer of Diodes Incorporated. As used herein: A. Life support devices or systems are devices or systems which: 1. are intended to implant into the body, or 2. support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in significant injury to the user. B. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or to affect its safety or effectiveness.
Customers represent that they have all necessary expertise in the safety and regulatory ramifications of their life support devices or systems, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of Diodes Incorporated products in such safety-critical, life support devices or systems, notwithstanding any devices- or systems-related information or support that may be provided by Diodes Incorporated. Further, Customers must fully indemnify Diodes Incorporated and its representatives against any damages arising out of the use of Diodes Incorporated products in such safety-critical, life support devices or systems. Copyright (c) 2010, Diodes Incorporated www.diodes.com
AP7165
Document number: DS31252 Rev. 6 - 2
14 of 14 www.diodes.com
September 2010
(c) Diodes Incorporated

▲Up To Search▲

Price & Availability of AP716510

	To Download AP716510 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .